- Updated to Redesign of the webinterface
- Befehl: system upgrade updatelatest
General
- The new firmware is downloaded by the UTM completely independently, but the new update is not activated without consent
- The UTM checks once an hour for a possible update
- Due to the update distribution system, it is possible that the update will not be obtained immediately.
It is not possible to skip this distribution processIf an update is urgently required, although the distribution process does not yet provide it, an image can be downloaded via the Reseller Portal. This can be used as a boot image. For hardware UTMs, physical access to the device is required for this. - The UTM always downloads a complete firmware image for the corresponding version
Command | Description |
---|---|
Check for update and download | |
system upgrade info | indicates which versions are available on the system.
Inside the system the command update is used for updating after entering new parameters (e.g.: system interface update after entering a new IP address). A new software version represents a new operating system version (firmware) and is a upgrade within the system. As a return there is a listing of max. 3 versions. firewall.foo.local>system upgrade info name|version ----+------- old |12.6.0 cur |12.6.0.1 new |12.6.1 firewall.foo.local> This system has been updated from 12.6.0 to the now active version 12.6.0.1 and an update to version 12.6.1 is available. |
system upgrade update | If no new version is available on the UTM new | none, this command can be used to check whether an update is available.
firewall.foo.local>system upgrade update -- empty answer from 'spupdater' firewall.foo.local> If a new version was loaded successfully, there is no error message ('empty answer'). But even with a 'parse error' a version was loaded. |
system upgrade updatelatest | Manueller Download der neuesten Firmware, auch wenn diese UTM noch nicht in der normalen Verteilung vorgesehen ist. |
system upgrade forceupdate | Deletes the new directory and performs a download if more recent software is available. |
system upgrade hint | Outputs what options are available at the current time.
firewall.foo.local>system upgrade hint message ------- dryrun, rollback firewall.foo.local> |
Rollback | |
system upgrade rollback | Performs a rollback. The previous version is reactivated. notempty Configuration changes in the new version are reset in the process. notempty The UTM system restarts automatically
|
Update | |
system upgrade dryrun | Performs an update to the version listed in the new line. notempty The UTM system restarts automatically
firewall.foo.local> system upgrade dryrun Broadcast Message from root@firewall.foo.local (somewhere) at 14:12 ... the system is going down for reboot soon message ------- going down for reboot Once the system is restarted, a new login is required. firewall.foo.local> system upgrade hint message ------- finalize firewall.foo.local> To permanently complete the update, the command system upgrade finalize is still required. . Before this, a factory reset must not be performed under any circumstances! |
Eula acceptance | |
system upgrade confirm eula | Acceptance of the EndUserLicenceAgreement. Eula must be accepted.
firewall.foo.local> system upgrade hint message ------- confirm eula finalize, decline firewall.foo.local> |
Privacy policy acceptance | |
system upgrade confirm privacy | Acceptance of the privacy policy. The privacy policy must be accepted.
firewall.foo.local> system upgrade hint message ------- confirm privacy finalize, decline firewall.foo.local> |
Eula and privacy policy rejection | |
system upgrade decline | Rejection of the eula and privacy policy. The update cannot be installed in this case. |
Set startup version | |
system upgrade finalize | When this command is used, this version is used permanently. Otherwise, the system would start again with the previous version when rebooting.
firewall.foo.local> system upgrade finalize firewall.foo.local> Verification that the new version is now also displayed as the currently running version: firewall.foo.local> system upgrade info name|version ----+------- old |12.6.0.1 cur |12.6.1 new |none Here the version running before the update should now be listed under old and the new version accordingly as cur. The command system upgrade hint now returns: firewall.foo.local> system upgrade hint message ------- rollback Here only "rollback" should be returned. |