KKeine Bearbeitungszusammenfassung |
Update 14.1.0 II>AlexandraK Keine Bearbeitungszusammenfassung |
||
| Zeile 35: | Zeile 35: | ||
{{var | cli--config-sync | {{var | cli--config-sync | ||
| Durch diesen Befehl kann die jeweilige Start-Konfiguration über die Hotwire Schnittstelle an den Cluster Partner übertragen werden. <br> {{Hinweis-box||g}} Dabei wird die Konfiguration von der UTM verwendet, auf der der Befehl ausgeführt wird.<br> {{Hinweis-box||gr}}Ein Artikel zu den ''system''-Befehlen findet sich [[UTM/CLI/System | hier]]. | | Durch diesen Befehl kann die jeweilige Start-Konfiguration über die Hotwire Schnittstelle an den Cluster Partner übertragen werden. <br> {{Hinweis-box||g}} Dabei wird die Konfiguration von der UTM verwendet, auf der der Befehl ausgeführt wird.<br> {{Hinweis-box||gr}}Ein Artikel zu den ''system''-Befehlen findet sich [[UTM/CLI/System | hier]]. | ||
| With this command the respective start configuration can be transferred to the Cluster Partner via the Hotwire interface.<br> {{Hinweis-box||g}} The configuration from the UTM on which the command is executed is used.<br> {{Hinweis-box||gr}} An article of ''system'' commands can be found [ | | With this command the respective start configuration can be transferred to the Cluster Partner via the Hotwire interface.<br> {{Hinweis-box||g}} The configuration from the UTM on which the command is executed is used.<br> {{Hinweis-box||gr}} An article of ''system'' commands can be found [{{#var:host}}UTM/CLI/System here]. }} | ||
{{var | cli--value-get | {{var | cli--value-get | ||
| Zeigt den Delay in Sekunden an, bevor im Fehlerfall, von Master auf Backup geschaltet wird. Der Standardwert ist 2 Sekunden. | | Zeigt den Delay in Sekunden an, bevor im Fehlerfall, von Master auf Backup geschaltet wird. Der Standardwert ist 2 Sekunden. | ||
| Zeile 47: | Zeile 47: | ||
{{var | bzw. | {{var | bzw. | ||
| bzw. | | bzw. | ||
| | | resp. }} | ||
{{var | Wartungsmodus Status--desc | {{var | Wartungsmodus Status--desc | ||
| Gibt aus ob der Wartungsmodus aktiv ist (''1'') oder nicht (''0'') | | Gibt aus ob der Wartungsmodus aktiv ist (''1'') oder nicht (''0'') | ||
| | | Outputs whether maintenance mode is active (''1'') or not (''0'') }} | ||
{{var | CLI-Wartungsmodus aktivieren--desc | {{var | CLI-Wartungsmodus aktivieren--desc | ||
| Aktiviert den Wartungsmodus<br> | | Aktiviert den Wartungsmodus<br> | ||
| Zeile 58: | Zeile 58: | ||
| Activates the maintenance mode<br> | | Activates the maintenance mode<br> | ||
* The maintenance mode is used to switch to the spare in a controlled manner and prevents multiple switching in the case of several individual steps (update, change IP addresses etc.) | * The maintenance mode is used to switch to the spare in a controlled manner and prevents multiple switching in the case of several individual steps (update, change IP addresses etc.) | ||
* The services available in maintenance mode are configured in the wizard in step 4 or under {{Menu|Network|Cluster configuration|Applications}}. | * The services available in maintenance mode are configured in the wizard in step 4 or under {{Menu-UTM|Network|Cluster configuration|Applications}}. | ||
* The UTM is not accessible via the virtual IP in maintenance mode, but only via a fixed IP address. }} | * The UTM is not accessible via the virtual IP in maintenance mode, but only via a fixed IP address. }} | ||
{{var | CLI-Wartungsmodus deaktivieren--desc | {{var | CLI-Wartungsmodus deaktivieren--desc | ||
UTM/CLI/Cluster.lang: Unterschied zwischen den Versionen
Aus Securepoint Wiki