KKeine Bearbeitungszusammenfassung |
KKeine Bearbeitungszusammenfassung |
||
Zeile 34: | Zeile 34: | ||
| If a configuration change has been made in the CLI, it must be saved locally first. Only then is a synchronization of the cluster transferred. }} | | If a configuration change has been made in the CLI, it must be saved locally first. Only then is a synchronization of the cluster transferred. }} | ||
{{var | cli--config-sync | {{var | cli--config-sync | ||
| Durch diesen Befehl kann die jeweilige Start-Konfiguration über die Hotwire Schnittstelle an den Cluster Partner übertragen werden. <br> {{Hinweis- | | Durch diesen Befehl kann die jeweilige Start-Konfiguration über die Hotwire Schnittstelle an den Cluster Partner übertragen werden. <br> {{Hinweis-box||g}} Dabei wird die Konfiguration von der UTM verwendet, auf der der Befehl ausgeführt wird.<br> {{Hinweis-box||gr}}Ein Artikel zu den ''system''-Befehlen findet sich [[UTM/CLI/System | hier]]. | ||
| With this command the respective start configuration can be transferred to the Cluster Partner via the Hotwire interface.<br> {{Hinweis- | | With this command the respective start configuration can be transferred to the Cluster Partner via the Hotwire interface.<br> {{Hinweis-box||g}} The configuration from the UTM on which the command is executed is used.<br> {{Hinweis-box||gr}} An article of ''system'' commands can be found [[UTM/CLI/System | here]]. }} | ||
{{var | cli--value-get | {{var | cli--value-get | ||
| Zeigt den Delay in Sekunden an, bevor im Fehlerfall, von Master auf Backup geschaltet wird. Der Standardwert ist 2 Sekunden. | | Zeigt den Delay in Sekunden an, bevor im Fehlerfall, von Master auf Backup geschaltet wird. Der Standardwert ist 2 Sekunden. | ||
| Displays the delay in seconds before switching from master to backup in case of an error. The default value is 2 seconds. }} | | Displays the delay in seconds before switching from master to backup in case of an error. The default value is 2 seconds. }} | ||
{{var | cli--value-set | {{var | cli--value-set | ||
| Verändert den Delay, für den Fehlerfall, das von Master auf Backup geschaltet wird. Der Standardwert ist 2 Sekunden und sollte nicht niedriger eingestellt werden. Falls die Appliances im Cluster eine hohe Grundlast haben sollten, kann der Wert höher eingestellt werden. <br> {{Hinweis- | | Verändert den Delay, für den Fehlerfall, das von Master auf Backup geschaltet wird. Der Standardwert ist 2 Sekunden und sollte nicht niedriger eingestellt werden. Falls die Appliances im Cluster eine hohe Grundlast haben sollten, kann der Wert höher eingestellt werden. <br> {{Hinweis-box||g}} Die Einstellung ist sofort aktiv und kann via ''system config synchronize'' auf den Partner übertragen werden. | ||
| Changes the delay, for the case of an error, which is switched from master to backup. The default value is 2 seconds and should not be set lower. If the appliances in the cluster have a high base load, the value can be set higher. <br>{{Hinweis- | | Changes the delay, for the case of an error, which is switched from master to backup. The default value is 2 seconds and should not be set lower. If the appliances in the cluster have a high base load, the value can be set higher. <br>{{Hinweis-box||g}} The setting is immediately active and can be transferred to the partner via ''system config synchronize''. }} | ||
{{var | Wartungsmodus | {{var | Wartungsmodus | ||
| Wartungsmodus | | Wartungsmodus | ||
Zeile 63: | Zeile 63: | ||
| Zustand während des gesetzten "Maintenance Mode" auf der '''Spare''' | | Zustand während des gesetzten "Maintenance Mode" auf der '''Spare''' | ||
| State during the set "Maintenance Mode" on the '''Spare''' }} | | State during the set "Maintenance Mode" on the '''Spare''' }} | ||
---- | ---- |
UTM/CLI/Cluster.lang: Unterschied zwischen den Versionen
Aus Securepoint Wiki