K 1 Version importiert |
K 14.2.0 |
||
| Zeile 21: | Zeile 21: | ||
| Ausgabe | | Ausgabe | ||
| Output }} | | Output }} | ||
{{var | cli--cluster-info | |||
| Cluster Status Meldungen der aktuellen UTM | |||
| }} | |||
{{var | cli--cluster-info--desc | {{var | cli--cluster-info--desc | ||
| | | Gibt an welche Rolle eine UTM im Cluster gerade hat: | ||
| | * ''Primary'': Gerät ist die aktive Cluster-UTM | ||
* ''Spare'': Gerät ist die passive Cluster-UTM (Backup bzw. Hot-Standby) | |||
* ''disabled'': Es ist kein Cluster konfiguriert | |||
| }} | |||
{{var | cli--sync-state | {{var | cli--sync-state | ||
| Gibt an, in welchem Zustand sich die Konfiguration befindet. | | Gibt an, in welchem Zustand sich die Konfiguration befindet. | ||
* ''synchronized'': Die Konfiguration ist auf beiden UTMS des Clusters gleich | |||
* ''pending'': Die Konfiguration der UTMs haben einen unterschiedlichen Stand. <br>In beiden Fällen können die Mitglieder miteinander kommunizieren. | |||
* ''error'': Die beiden UTMs können keine Daten austauschen<br>Das könnte z.B. der Fall sein, wenn kein Hotwire Interface konfiguriert ist, die Verkabelung nicht korrekt ist, falsche SSH Keys verwendet oder nicht ausgetauscht wurden oder falls die Gegenstelle offline bzw. down ist | |||
* ''disabled'': Es ist kein Cluster konfiguriert {{Hinweis-box|{{#var:neu ab}} v14.2.0|gr|14.2.5|status=neu}} | |||
| }} | |||
{{var | cli--hotwire | {{var | cli--hotwire | ||
| Gibt das Interface an, auf dem das Hotwire Interface konfiguriert ist. | | Gibt das Interface an, auf dem das Hotwire Interface konfiguriert ist. | ||
| Specifies the interface on which the Hotwire interface is configured. }} | | Specifies the interface on which the Hotwire interface is configured. }} | ||
{{var | cli--maintenance--desc | |||
| Gibt an, ob die UTM im Wartungsmodus (''true'') ist oder nicht (''false'') | |||
| }} | |||
{{var | cli--config-save | {{var | cli--config-save | ||
| Falls in der CLI eine Konfigurationsänderung durchgeführt wurde, muss diese erst lokal gespeichert werden. Erst dann wird eine Synchronisierung des Clusters übertragen. | | Falls in der CLI eine Konfigurationsänderung durchgeführt wurde, muss diese erst lokal gespeichert werden. Erst dann wird eine Synchronisierung des Clusters übertragen. | ||
| Zeile 37: | Zeile 50: | ||
| With this command the respective start configuration can be transferred to the Cluster Partner via the Hotwire interface.<br> {{Hinweis-box||g}} The configuration from the UTM on which the command is executed is used.<br> {{Hinweis-box||gr}} An article of ''system'' commands can be found [{{#var:host}}UTM/CLI/System here]. }} | | With this command the respective start configuration can be transferred to the Cluster Partner via the Hotwire interface.<br> {{Hinweis-box||g}} The configuration from the UTM on which the command is executed is used.<br> {{Hinweis-box||gr}} An article of ''system'' commands can be found [{{#var:host}}UTM/CLI/System here]. }} | ||
{{var | cli--value-get | {{var | cli--value-get | ||
| Zeigt den Delay in Sekunden an, bevor im Fehlerfall, von | | Zeigt den Delay in Sekunden an, bevor im Fehlerfall, von der Primary-UTM auf die Spare-UTM geschaltet wird. Der Standardwert ist 2 Sekunden. | ||
| Displays the delay in seconds before switching from | | Displays the delay in seconds before switching from primary to spare in case of an error. The default value is 2 seconds. }} | ||
{{var | cli--value-set | {{var | cli--value-set | ||
| Verändert den Delay, für den Fehlerfall, das von | | Verändert den Delay, für den Fehlerfall, das von der Primary auf die Spare geschaltet wird. Der Standardwert ist 2 Sekunden und sollte nicht niedriger eingestellt werden. Falls die Appliances im Cluster eine hohe Grundlast haben sollten, kann der Wert höher eingestellt werden. <br> {{Hinweis-box||g}} Die Einstellung ist sofort aktiv und kann via ''system config synchronize'' auf den Partner übertragen werden. | ||
| Changes the delay, for the case of an error, which is switched from | | Changes the delay, for the case of an error, which is switched from the primary to the spare. The default value is 2 seconds and should not be set lower. If the appliances in the cluster have a high base load, the value can be set higher. <br>{{Hinweis-box||g}} The setting is immediately active and can be transferred to the partner via ''system config synchronize''. }} | ||
{{var | Wartungsmodus | {{var | Wartungsmodus | ||
| Wartungsmodus | | Wartungsmodus | ||
| Zeile 64: | Zeile 77: | ||
| Disables the maintenance mode }} | | Disables the maintenance mode }} | ||
{{var | Zustand Wartungsmodus Master--desc | {{var | Zustand Wartungsmodus Master--desc | ||
| Zustand während des gesetzten | | Zustand während des gesetzten '''Maintainance Mode''' auf der '''Primary''' | ||
| State during the set "Maintainance Mode" on the ''' | | State during the set "Maintainance Mode" on the '''Primary''' }} | ||
{{var | Zustand Wartungsmodus Spare--desc | {{var | Zustand Wartungsmodus Spare--desc | ||
| Zustand während des gesetzten | | Zustand während des gesetzten '''Maintenance Mode''' auf der '''Spare''' | ||
| State during the set "Maintenance Mode" on the '''Spare''' }} | | State during the set "Maintenance Mode" on the '''Spare''' }} | ||
UTM/CLI/Cluster.lang: Unterschied zwischen den Versionen
Aus Securepoint Wiki