notempty
notempty
notempty Dieser Artikel bezieht sich auf eine nicht mehr aktuelle Version!
notempty
Der Artikel für die neueste Version steht hier
Zu diesem Artikel gibt es bereits eine neuere Version, die sich allerdings auf eine Beta-Version bezieht
Instructions for installing a Securepoint UTM G5 in a server rack.
Last adaption: 12.2021
New:
- Installation instructions for the Basic Kit for the RC100
- Installation instructions for the Premium Kit for the RC100
- Installation instructions for the Premium Kit for the RC200
- Video tutorial
This article refers to a Beta version
Specification
notemptyHint
- For reliable operation of our hardware throughout its life cycle, it must be operated within its specifications:
- The maximum ambient temperature for operation is 40°C
- The minimum ambient temperature for operation is 0°C
- Relative humidity must be between 10% and 80% and condensation must be prevent
- The maximum ambient temperature for operation is 40°C
- For installation, make sure that the firewall is mounted/set up as follows:
- Sufficient supply of cool air
- The device must not be covered
- The device must be as free-standing as possible
- When mounting in a network rack, special attention must be paid to:
- The rack must be ventilated
- Passively cooled devices (Black Dwarf G3+G5, RC100 G3, RC200 G3) must not be placed directly below or above heat emitting devices.
- There must be no build-up of heat
RC100 Basic Kit
Fig. 1
Step 1
- Mounting bracket for the sides
Fig. 2
Step 2
- Mounting bracket leaves ventilation outlet free
Fig. 3
Step 3
- Fasten mounting bracket laterally
Fig. 4
Step 4
- Fasten mounting bracket on the second side
Fig. 5
Step 5
- Space requirement in server rack: 1U
Fig. 6
Step 6
- Attach mounting bracket to the rack with the large silver screws
Done
RC100 Premium Kit
Fig. 1
Step 1
- Mounting bracket left (narrow) and right (wide)
Fig. 2
Step 2
- supplied patch cable
Fig. 3
Step 3
- Mounting bracket for power supply unit(s)
Fig. 4
Step 4
- The narrow mounting bracket goes on the left side of the UTM
Fig. 5
Step 5
- The ventilation outlet remains free
Fig. 6
Step 6
- Mounting with two black screws
Fig. 7
Step 7
- The wide mounting bracket with the power supply and network connections is mounted on the right side.
Fig. 8
Step 8
- Fastening again with two black screws
Fig. 9
Step 9
- Mounting bracket for the power supply unit
Fig. 10
Step 10
- Screw the mounting bracket tight from below
Fig. 11
Step 11
- Attached power supply with connection to the UTM.
- The cable should be neatly routed later
Fig. 12
Step 12
- Plug in the patch cable at the back
- and fasten at the front at the correspondingly labeled opening with the silver screws
The label follows the arrangement of the status lights on the front side of the UTM
Fig. 13
Step 13
- The UTM requires 1U
Fig. 14
Step 14
- Screwing with the large silver screws
- in the picture above
RC200 Premium Kit
Fig. 1
Step 1
- Mounting bracket left (narrow) and right (wide)
Fig. 2
Step 2
- Included LC fiber optic cable
Fig. 3
Step 3
- Included LC fiber optic cable
Fig. 4
Step 4
- Mounting bracket for 2 power supplies
Fig. 5
Step 5
- The narrow mounting bracket goes on the left side of the UTM
Fig. 6
Step 6
- Mounting with two black screws
Fig. 7
Step 7
- The wide mounting bracket with the power supply and network connections is mounted on the right side.
- Mounting also with two black screws
Fig. 8
Step 8
- Screw down the mounting bracket for the power supply units from below
Fig. 9
Step 9
- Plug in the patch cable at the back
- and fasten at the front at the correspondingly labeled opening with the silver screws
The label follows the arrangement of the status lights on the front side of the UTM
Fig. 10
Step 10
- Plug the supplied SFP module into port A4 on the UTM and plug in the supplied LC fiber cable.
Fig. 11
Step 11
- Push through the connector for the SFP port from the inside with the long end facing outward
Fig. 12
Step 12
- Fastening the connector for the LC fiber optic cable
Fig. 13
Step 13
- Insert the LC fiber optic cable into the connector
Fig. 14
Step 14
- The UTM requires 1U
Fig. 15
Step 15
- Screwing with the large silver screws
- in the picture above
RC300S
Preparation
- Screwdriver type Ph2 (not enclosed).
- Screws supplied:
- 4 small black screws (M2x4 countersunk head)
- 4 large silver screws (M5x15 flat head)
Instructions
Fig. 1
Step 1
- Mounting bracket for the sides
Fig. 2
Step 2
- Attach mounting bracket to the side
Fig. 3
Step 3
- Screws to hold the mounting brackets in the rack
Fig. 4
Step 4
- Two screws each hold the mounting brackets in the rack
Fig. 5
Step 5
RC350R - RC1000R
Preparation
- Screwdriver type Ph2 (not enclosed)
- Premium mounting rails
- From the enclosed screw sets:
- 4 thick black screws (M2x4 countersunk head)
- 6 smaller black screws (M1x2 countersunk head)
- 4 small silver-coloured screws (M4x4 flat head)
- 2 large silver-coloured screws (M5x15 flat head)
- 2 large silver-coloured screws with spacer (M5x15 flat head with shoulder)
Instructions
Fig. 1
Step 1
- Components of a mounting bracket
Fig. 2
Step 2
- Assemble the mounting brackets with the larger black screws
Fig. 3
Step 3
- Attach the mounting bracket to the enclosure with the smaller black screws
Fig. 4
Step 4
- Release the lock with the help of the small lever
- Remove the inner rail from the guide rail
Fig. 5
Step 5
- Inner rail with small fixing screws
Fig. 6
Step 6
- Mount the inner rail
Fig. 7
Step 7
- Repeat steps #01 - #06 on the other side
Fig. 8
Step 8
- Pull back the bolt of the fastening device at the end of the guide rail to hook it in
Fig. 9
Step 9
- Suspended premium guide rail
Fig. 10
Step 12
- Screws for fixing the guide rails
Fig. 11
Step 10
- Attach guide rails to the back of the rack
- Tighten screws only hand-tight
Fig. 12
Step 11
- Pull the inner rails forwards
- To hook in the units, release the lock using the small lever
Fig. 13
Step 13
- Fit the screws at the front
- Tighten only slightly
Fig. 14
Step 14
